TierramadreLandscape.com

I recently picked up a set of low voltage outdoor lighting at a yard sale. The total watts for the lights equals 66 watts. The transformer is 44 watts. Will this set up work? And if so what are the consequences of using an undersized transformer.
Thanks

If the transformer has a fuse it will blow and if it doesn't then the transformer eventually burn out.

2009-06-01 12:23:27 by fawey

http://www.LumaStone.ca/store/ home.php?cat=259 LumaStone retaining wall lights are designed to be installed seamlessly into outdoor hardscape ...

Try emailing Westinghouse, they should be able to direct you to a retailer that carries what you are seeking.

2009-04-09 11:03:53 by Rocky S

Price: $348.00 $232.00

4-1/2-Inch width x 10-Inch height x 4-Inch depth
10 year warranty
UL listed

I just installed a new switch (provides power to the landscaping lights) & receptacles. Tapped off of an extra circuit from the basement. I connected the Hot & Neutral wires to one side of the receptacle, and ran Hot/Neutral from the other side of the receptacle to the switch (Hot - On/ Neutral - Off terminals). I also connected the Black/White wires from the outdoor lighting transformer with the same Hot/Neutral wires on the switch.

When the switch is in the ON position, & the Circuit Breaker is turned ON - All is good. Light work. Receptacle works. However, when I turn OFF the light switch & then turn it back ON, it trips the circuit breaker ever time ?? What did I do wrong ??

Any advise would be greatly appreciated !

Thanks.

BVW
JN Thanks for the input. I have the ground wire coming from the ROMEX connected to both the Switch & the Receptacle. S/B Grounded.

Okay, I Think you ran the wires wrong, but it is hard to tell by your description.

Black=Hot
White=Neutral.

Run white from existing circuit to lights with no breaks/interruptions.

Run black wire to switch. cut, wire one end to each screw on the switch.

you said
"I also connected the Black/White wires from the outdoor lighting transformer with the same Hot/Neutral wires on the switch."


You can't have both black and white wires connected to a switch. It sounds like you wired the blacks together and then wired both black and white to the switch on the off side. when you switch it off, you are throwing black and white together.

2007-09-24 07:40:37 by bvwfootball

Price: $297.00 $198.00

10 year warranty
UL listed
3-1/2-Inch width x 13-Inch depth x 4-Inch depth

I use several of these Malibu 120v to 12v transformrs to light my yard. But I am having a difficult time figuring out what they are costing me. My transformers are for outdoor use, but I thought a while back people were putting in low voltage interior can lights because they were in the long run cheaper to run? I want to calculate what each Malibu costs me per month.

300 watts, times the hours they run per day, times 30 days, divided by 1000, times the cost per kilowatt hour your power company charges. 8 to 18 cents depending where you are.

300x12x30 \ 1000 = 108 KWH x .10 = $10.80 per month

2008-01-27 10:46:04 by segaultney

Just installed a 600 watt Ryco Engineering landscape lighting transformer a week ago. Worked fine until today. The digital display on the unit turns on and functions as normal, however I am measuring 0 voltage on every setting. The breakers are not tripped and the wiring looks fine. Unit looks fine and does not smell burnt. Is there anything I could be missing on trouble shooting this? I would hate to have to replace it after only a week.

It sounds like a bad connection. Take your tickler and check the input voltage. Is there a thermal switch? Lots of times a non-professional will not make a solid connection. It could also be cross wired, they will work for a while sometimes that way. Black or red to hot, white to neutral.

2008-08-07 16:19:54 by joeworkman1